辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

A model of PEMFC-battery system to evaluate inner operating status and energy consumption under different energy management strategies

A hybrid system with jointed battery and PEMFC is popular and of great potential in New Energy Vehicle (NEV) application. However, reliability and efficiency remain to be improved for commercial products. To reflect the complicated physics inside the proton exchange membrane fuel cell (PEMFC), the PEMFC model consisting of inner muti-physics process and other accessories was built, then a complete hybrid system was established when a matched battery, DC/DC, regenerative braking were taken into consideration. Based on the above model, the stack state and system performance under standard cycle for heavy duty vehicle-CWTVC were obtained. According to the simulation results, fuel cell states such as pressure, water content and voltage suffers severe oscillation with external load, especially in the highway cycle. Membrane electrode assembly (MEA) suffers from pressure impact with average value of more than 24 kPa in highway cycle. In the aspect of relative humidity, the PEMFC stack is most threatened in road cycle. As for the hybrid system, its efficiency and state of charge (SOC) fluctuation perform worst in urban cycle and road cycle respectively, while its highest efficiency occurs in road test. Operating mode of fuel cell has influence on hybrid system. When 3-level mode of fuel cell output was applied, the efficiency increased to its peak value at medium level of 28 kW and then declined gradually. H₂ consumption had an opposite trend compared to efficiency. In the aspect of battery SOC, it declines in operating process and its fluctuations decreases when medium level got bigger. The 3-level mode and 4-level mode were compared using this model. It can be concluded that although 3-level mode performs slightly better in hybrid system efficiency, H₂ consumption, pressure impact, it does not have absolute advantage over 4-level mode in other indicators.     

Anisotropy Effects in the Shape-Memory Performance of Polymer Foams

Isotropic and anisotropic shape-memory polymer foams are prepared by supercritical carbon dioxide foaming from a multiblock copolymer (PDLCL) consisting of poly(ω-pentadecalactone) and poly(ε-caprolactone) segments. Analysis by micro-computed tomography reveals for the anisotropic PDLCL foam cells a high shape anisotropy ratio of R = 1.72 ± 0.62 with a corresponding Young's compression moduli ratio between longitudinal and transversal direction of 4.3. The experimental compression data in the linear elastic range can be well described by the anisotropic open foam model of Gibson and Ashby. A micro-morphological analysis for single pores using scanning electron microscopy images permits the correlation between the macroscopic stress-compression behavior and microscale structural changes.     

单晶硅表层机械力学特性的各向异性分析

为探究挠性筋结构单晶硅材料的各向异性特性以及KOH腐蚀工艺对其力学性能的影响规律,进行纳米压痕实验,并结合原子力显微镜观察单晶硅表层3个主晶面上压痕裂纹形貌随晶向的变化规律,分析单晶硅材料表层弹性模量、硬度、断裂韧性等机械力学特性参数在(001)、(110)及(111)3个主要晶面上沿各个晶向的变化规律;分析挠性筋结构单晶硅材料(001)晶面的KOH腐蚀工艺对其材料表面机械特性的影响规律.结果表明:挠性筋单晶硅在(001)晶面上弹性模量的各向异性变化幅度明显,硬度及断裂韧性各向异性的变化幅度不大;挠性筋单晶硅在(110)晶面弹性模量和断裂韧性的各向异性变化幅度明显,硬度各向异性变化幅度不大;挠性筋单晶硅在(111)晶面硬度值、弹性模量及断裂韧性参数的变化幅度幅值均较小;确定了单晶硅表层3个晶面裂纹最易扩展的晶向方向,KOH腐蚀工艺使得单晶硅表面质量降低,腐蚀后暴露的表面微裂纹、缺陷等会使得单晶硅(001)晶面表层硬度、断裂韧性降低,从而降低了挠性筋结构的实际断裂强度.     

Correlation among hydrogenation,magnetoelastic coupling,magnetic anisotropy,and magnetoresistance in magnetostrictive,hydrogen-absorbing palladium-cobalt alloy films for hydrogen sensing

Hydrogen-absorbing magnetic alloy films, such as palladium-cobalt (PdCo) alloy films, are expected to play a significant role in the next generation of hydrogen sensors. However, effects of hydrogenation on such films are very complex, since these alloys show strong spin-orbit interaction, i.e., strong magnetoelastic coupling. Accordingly, we conducted integrated research on the hydrogenation, magnetoelastic coupling, magnetism, and galvanomagnetic effect of PdCo alloy films having different magnetic anisotropies of longitudinal and perpendicular magnetic anisotropies. As a result, it was revealed that the stress in the film determines its magnetic anisotropy. The magnetoresistance curves of films, consisting of ordinal and anisotropic magnetoresistance effects, correspond well to the magnetization-magnetic field curves. Hydrogenation results in the compressive stress and decreased magnetostriction, which both have a negative influence on the perpendicular magnetic anisotropy energy of the films. Moreover, the influence is observed also in ordinal and anisotropic magnetoresistances. In addition, the increases in coercivity and electronic resistivity due to the incorporated hydrogen atoms (and related defects) are detected. The results are summarized in a correlation diagram, which shows that hydrogen-absorbing magnetic alloy films are very suitable for use in hydrogen sensors—the films can detect hydrogen via various methods such as magnetic anisotropy, galvanomagnetic effect, coercivity, and resistivity.     

Screening of frozen-thawed conditions for keeping nutritive compositions and physicochemical characteristics of goat milk

Frozen milk can help producers overcome the seasonality of goat milk production, low goat production and short lactation periods, and avoid discarding milk during some special periods. We investigated effects of combination between freezing (cryogenic refrigerator of ?16 to ?20°C or ultra-cryogenic refrigerator of ?76 to ?80°C) and thawing (homeothermy of 20 to 25°C or refrigeration of 2 to 4°C) on nutritive compositions and physicochemical characteristics of raw goat milk during storage period (80 d). Compared with fresh goat milk, the frozen-thawed milk decreased contents of fat, protein, and lactose, as well as surface tension and stability coefficient, whereas increased effective diameter and polydispersity index. The average values of color values (L*, a*, and b*) in 4 group samples changed from 83.01 to 82.25, ?1.40 to ?1.54, 3.51 to 3.81, respectively, and the ΔE of most samples did not exceed 2. In contrast to the other 3 frozen-thawed treatments, goat milk treated with ultra-cryogenic freezing-homeothermic thawing (UFHT) possessed higher fat (5.20 g/100 g), smaller effective particle diameter (0.32 µm), and the lowest polydispersity index value (0.26). The color and confocal laser scanning microscopy images of UFHT were similar to those of fresh goat milk, illustrating UFHT was the optimal approach to maintain the natural quality of goat milk. Our finding provides a theoretical basis for producers to freeze surplus milk.     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.